Wiper seals manufacturer and supplier today

Rod seal factory 2024: A basic mechanical seal contains three sealing points. The stationary part of the seal is fitted to the pump housing with a static seal –this may be sealed with an o-ring or gasket clamped between the stationary part and the pump housing. Rotating and Stationary parts of a Seal – The rotary portion of the seal is sealed onto the shaft usually with an O ring. This sealing point can also be regarded as static as this part of the seal rotates with the shaft. The mechanical seal itself is the interface between the static and rotary portions of the seal. One part of the seal, either to static or rotary portion, is always resiliently mounted and spring loaded to accommodate any small shaft deflections, shaft movement due to bearing tolerances and out-of-perpendicular alignment due to manufacturing tolerances. Read extra information at rod seals.

Mechanical seals form a critical part of any mechanical operation involving fluid movement through rotational shafts, such as in the case of pumps. These seals ensure that the fluid does not leak out of a closed system and contaminants do not enter the system. In pumping applications, mechanical seals are placed at the point of entry or exit of a rotating shaft, preventing the pressurized fluid from escaping the pump housing and withstanding the friction generated from the shaft rotations. Read on to learn how mechanical seals work and explore some popular use cases of seals in pump applications.

However, hydraulic transmission also has disadvantages compared with mechanical transmission: It is easy to leak and not friendly to the environment. High manufacturing precision is required. Low efficiency. The transmission ratio is not fixed. Due to the special working environment of construction machinery, its hydraulic system has the following characteristics: The working hours are irregular, and sometimes work continuously for a long time. The working environment is outdoors, the working temperature difference is large, and the working environment is dusty. The machine itself walks. Due to the limitation of volume and weight, the hydraulic oil tank is generally relatively small. Due to the volume and weight, the working pressure of the hydraulic system is high, usually above 20MPa, and the highest is about 40Mpa.

The O-ring seal, which is also called shaft seal, is noted for a reasonable compression and stretch rate to achieve a good sealing effect. It will not leak when it is sealed statically. At the same time, the O-ring size is properly matched to the groove size. The structure is simple and its installation is very close to the machine. Its most prominent advantage is its self-sealing effect, eliminating the need for periodic adjustments. We guarantee that the size and mounting grooves of all our O-rings are standardized, so they are cost-effective and easy to maintain. They have low frictional resistance and are suitable for occasions where the pressure is often alternating.

Sealing performance over conventional O-rings is achieved by reducing particle generation, extending seal life and minimizing replacement time during preventive maintenance. Compared to traditional O-rings, this seal effectively reduces the number of dust particles generated during operation and extends the life of the machine with bonded seals installed. The seal has a working diameter range of 6.5 to 60.58mm.

DMS Seals piston seals can be used very effectively in the clearance between the two chambers of the hydraulic cylinder and cylinder. The piston seal is pushed by the pressure of the fluid. Its good working performance can improve the efficiency of the machine. Due to its excellent resistance to leakage, it helps the machine to extend the machine’s working life. Our seals provide the best tight adhesion for the sealing system with low internal leakage and frictional resistance.

The selection principle of the gasket: according to the working pressure, working temperature, the corrosiveness of the sealing medium and the form of the sealing surface. Temperature influence: In normal temperature and low pressure, use non-metallic soft honey gasket; in medium pressure and high temperature, choose metal and non-metal combination gasket or metal gasket; when temperature and pressure fluctuate greatly, choose good elasticity or self-tightening type Gaskets; in low temperature, corrosive media or vacuum conditions, gaskets with special properties should be considered.

DMS SEALS is a technology enterprise which specialized in the production of seals, the development of seals material and the solution of the sealing of special working condition. We own 120 staffs which including 70 middle and senior technicians. Our factory covers more than 10000 square meters which including 8000 square meters for the workshop. Our production equipment and test equipment are on leading level in the same industry. We are the one of the biggest enterprise who specialized in manufacturing and developing seals in China. We have long time cooperation and communication with many universities and research institutions at home and board. Find more info on https://www.dmsseals.com/.

DMS Seals is a scientific and technical mechanical seal manufacturer and oil seal supplier specializing in seal production, sealing material development, and the conception of sealing solutions for special working conditions. We have 120 employees, including 70 senior technicians. DMS Seals has a number of invention patents and leading production processes. The R&D team is able to design and develop Rubber Seal & Hydraulic Seals for various mechanical sealing systems under complex conditions. We have already passed the certification of ISO 9001 and TS 16949.